Recent content by AlexandreTheGreatBR

Although we know that the WiFi circuit must be completed, which is causing problems and that the console cannot even connect to the internet via cable, when we make an attempt we receive an error message 80020102... even when we change cell and nand the connection via cable should work perfectly...

Although we know that the WiFi circuit must be completed, which is causing problems and that the console cannot even connect to the internet via cable, when we make an attempt we receive an error message 80020102... even when we change cell and nand the connection via cable should work perfectly...

Felix, a friend of mine, did an experiment after realizing that his Cech b's CELL was beyond repair due to oxidation of the pads. instead of just changing the board for one from a cech A, he replaced both the damaged cell and the nand and the syscon from cech a to b, to top it off he made a...

I have the same problem as you and the coincidences are not just that, my PS3 is an A00 with a 40nn RSX but unlike yours, mine was not made by Sony, anyway after a few months it started to present problems with o the ps2 games, first freezing during the game and now just a black screen...

I had the same problem on my CECHA00 Frankie, if the temperature is below 60 the ps2 games freeze although it is possible to access the menu and return to xmb or restart the game... above 60 they run smoothly... considering that I live in Brazil temperatures above 60 degrees are easily achievable

Are you brazilian? Enviado de meu SM-A037M usando o Tapatalk

E bom ver outro brasileiro por aqui! e se interessando em fazer o mod que maravilha! conheci um técnico mês passado que já havia feito com sucesso a modificação e esse ontem ele finalizou o serviço no meu CECHA00, pretendo postar isso por aqui em breve pra divulgar o serviço dele e espero que...

Amazing! i live in brazil and unfortunately there is no one who is interested in learning this mod so i'm trying to learn the process by myself, i pulled an rsx from a slim but i ended up damaging 2 pad of the rsx... i would like to send it out to the fees that my country would charge for him to...

hello everyone, I'm trying to learn how to perform the whole process of a frankie and today I removed an rsx from a donor card, a cdx5301a1gb... but unfortunately during the process I damaged the tracks of the donor card and apparently two pads from the rsx were ripped off , one from gnd and one...

Hello guys, I have a cech eo1 that is showing the following error log: Firmware Version: 4.90 (build 50696) Platform ID: CokB10 Product Code: 00 82 Product Sub Code: 00 03 Hardware Config: 20000000FFFFFEFF Syscon Fimware Version: 0DBF.0001000300030002 (EEPROM: 0001000300030002) Bringup Count...

Good to know but unfortunately I ended up damaging one of the pads again, the jumper got stuck on my shirt the moment I got up it ended up breaking the pad... there's something wrong with that board... anyway I'll leave it as scrap but thanks for the information

hello major thanks for answering, but it is not necessary to connect resistors at specific points to make these points be activated? I had read old posts and that this was necessary but I didn't get to the new ones to find out if the problem had been overcome or identified... just make the...

sorry for asking after so long but did you find out how to reconnect the alternate points? I have a cok-001 in which the 3 pads are damaged...

man if I told you that I already installed a cfw on it (evilnat 4.90) on the second day that it came back to work the first time? I confess that I didn't think for a moment about the possibility of him dying in the middle of the process... I was excited! but everything went well and I have a...

So, unfortunately I don't have much information about it because I found it in an electronics disposal store, when I turned it on, ylod, then opened it (it wasn't sealed) and I found that someone had already installed tantalum capacitors next to the nec/tokin but that's all without other signs...