Recent content by dumbass370

Well i guess i found the problem, will try to fix it now, hope it works Yep, after fixing it console starts, but turns out it has GLOD, SB log verified RSX driver timeout so gonna frankie mod it with 40nm chip

5 kOhm on 12V pins, seems fine to me I'll check syscon later, don't have the console on hands right now

Hey guys, having a problem with a CECHB console Took it to 2 local repair guys, they claim power rail itself is good and that either rsx is causing short or scratched cell after delid, though previous owner told me it worked fine like that with solder mask on the scratch Anyway scratched CELL...

RSX swap didn't help, error is stil 0xa0403034

Yes but it can easily be CPU itself or South Bridge, i don't know how to check it

Hello, i have a YLOD CECHA12, error is 0xa0403034 alone, nothing else Warming RSX up with hot air gun didn't do anything and also the fact that SB UART log is silent worries me I did enter the command to activate sb uart, tried tx and rx wires - no luck I did it before on another console so...

Hello guys, i recently had 3 cecha and 1 cechb arrived from Japan and i proceeded to fixing them CECHB was having YLOD, turned out to be a nec/tokin problem, after replacement it started to work Right after N/T replacement it worked for 5-10 minutes, then i delided both chips, it started once...

Hello guys, I harvested a 40-nm rsx from slim MB, some measurements look a bit low to me, can anyone confirm if this RSX is okay? Want to install it onto COK-001 board Sorry I don't know how to hide image under a spolier, if moderator sees this - please do) Anyways, I installed it. At first it...

Will try, ty Only got 1 good mb left

Hello guys I made myself a BGA soldering station - Puhui 8280 + ACHI6500 top heater Machine itself works fine, but i already ruined 2 rsx - both had vram bleed no matter what i did, i happens at 200 degrees Somehow before that i managed to remove another dead 90-nm rsx without an issue I guess...

YLOD Syscon error help. Hello guys I have a CECHK PS3 with DIA-002 mobo, bought it for cheap Turns on, works for 2-3 seconds, fan tries to speed up and then console beeps 3 times It is already delided, no damage there First time i opened it up and read the syscon, it had 5-6 3034/4102 But later...

Yes, checked that as well. Nvm, i sold it, i've had it for over 2 months now, second repair shop i gave it to said it could be the MechaCon chip, the guy buying it said the same, too complicated for me anyway

Hello I have a broken PS2 Fat with gh-001 mobo that doesn't turn on and has no standby light Problem is definetely not with PSU, output 8.5V as it should All fuses are good too both PSU and mobo (there are 15-20 of them) Tried repairing it in a local repair shop, the guy said its CXP101064...

Nvm, just figured out i was checking RSX power block..... Anyway, i checked the CELL IC6301 and..... got alm the same result, 50-60mv 7 pin and 2.5-3.5v 22 pin. Also swapped IC6301 between mobos, on the donor board it was showing 2.5-3v on pin 7 and 11.8v on 22 pin. Pls help guys, i feel like...

Hello fellas, i'm having 3003 syscon error with COK-002 mobo, tried swapping single CELL nec/tokin for 4 470uf 2.5v tantalum caps, didn't work, then i checked IC6201, pin 7 gives me 60mv instead of 3.3v, and pin 22 gives me 2.5-5v instead of 12. Tried replacing IC6201, took it from dead mobo...