Recent content by Max777x

  1. M

    PS3 4.93 Evilnat w/ Cobra v8.5 - (CEX/PEX/D-PEX)

    https://www.psx-place.com/threads/black-screen-after-installing-cfw-evilnat-warning-ros0-hash.45443/#post-403957
  2. M

    black screen after installing cfw evilnat WARNING! ROS0 Hash

    The problem in this topic is that cfw evilnat does not work for me (does not launch applications, freezes on a black screen), The problem in this topic is that cfw evilnat does not work for me (does not launch applications, freezes on a black screen), and they write useless advice to me...
  3. M

    black screen after installing cfw evilnat WARNING! ROS0 Hash

    thanks for the useless advice
  4. M

    black screen after installing cfw evilnat WARNING! ROS0 Hash

    Thank you, of course, for your concern, but will someone help me with my problem, or will there be more off-topic messages? or I'll finish my PlayStation...
  5. M

    black screen after installing cfw evilnat WARNING! ROS0 Hash

    how can I solve my problem then? can anyone give specific directions/solutions? I already formatted the hard drive and reinstalled the system. How can I make EVilNAT work? -- well yes of course... The BD drive interferes with heat dissipation, this is easy to understand
  6. M

    black screen after installing cfw evilnat WARNING! ROS0 Hash

    thanks for the answers. but can you be more specific? I don’t understand what ERK is. CFW evilNAT is now installed also unclear
  7. M

    black screen after installing cfw evilnat WARNING! ROS0 Hash

    черный экран после запуска webman/pkgi сразу после установки cfw evilnat webman/pkgi не запускается ошибка обнаружена в дампе, полученном через evilnat ПРЕДУПРЕЖДЕНИЕ! 009.02 Хэш ROS0 Япония, см. консоль CECHHL00. (ДИА-001) порядок действий был изначально - > установить 2 раза OFW 4.91 ->...
  8. M

    PS3 Fault finding YLOD with the SYSCON - First steps and Error reporting

    shit ((((( After replacing the bridge, the following errors appeared: next, i reset the codes and restarted as a result, there are errors indicating a malfunction of the RSX, but I'm not sure about this from heating, the textolite on the board swelled in some places, even under the bridge...
  9. M

    PS3 Fault finding YLOD with the SYSCON - First steps and Error reporting

    There are no signals from these 2 points that you indicated. changing the bridge...
  10. M

    PS3 Fault finding YLOD with the SYSCON - First steps and Error reporting

    what's in the photo? 2 points selected. I don't know what to do next with this board, I'm thinking of replacing the Southbridge, but I'm not sure. I think that rsx is alive
  11. M

    PS3 Fault finding YLOD with the SYSCON - First steps and Error reporting

    Can you provide a link for more details on where it is located? just read the dump and it's ok here's the log most likely there was a bad contact e3 flasher So what should I do?
  12. M

    PS3 Fault finding YLOD with the SYSCON - First steps and Error reporting

    i wrote the command w 4202 02 complete! further connected to SB_SIO0_TXD_M on motherboard launched PYtty COM3 settings 115200 but when running the console, there is nothing in the PYtty terminal Checked several times the soldering and the rest Only GND and TXD pins are connected to the board...
  13. M

    PS3 Fault finding YLOD with the SYSCON - First steps and Error reporting

    Is it possible to learn more about how to connect to SB uart? This board came to me with glod
  14. M

    PS3 Fault finding YLOD with the SYSCON - First steps and Error reporting

    motherboard DIA-001 ** GLOD ** UART no error I made a replacement for RSX with a similar one - the result returned to GlOD also tried to warm up SOUTH BRIDGE Resetting video settings doesn't help. no video by AV & HDMI power comes to the USB ports but there is no reading from a USB flash drive...
  15. M

    PS3 Fault finding YLOD with the SYSCON - First steps and Error reporting

    thanks for the answer, it's not clear what to do next, to warm up the RAM?
Back
Top