PS3 littlebalup's -- TEENSY2PS3 - PCB "linker" Teensy++2.0 <-> PS3

Ealier this month and prior to the recent update to "Way-Launcher" developer littlebalup has also presented a new project to the community called Teensy2PS3, which aims to be an Easy, Simple and Cheap solution for Flashing your PS3 NOR & NAND chips. The developer shares some pics and also provides the gerber files needed to manufacture the board . All the details can be seen below and also at the source links provided.

​

I present you my project of a simple PCB (printed circuit board) to facilitate the use of our teensy++2.0 for the flash of PS3 NOR and/or NAND:
​

Intent:

• Simple
• Cheap
• Easy (to use, to assemble...)
• Smallest as possible with board traces shorter as possible.
• Compatible NOR and NAND (SBE) and switchable/reversable between both.
• Compatible 360-Clips NOR and NAND.
• Usable with existing layouts and softwares (judges' ones), teensy equiped with voltage regulator or not, etc...
• Modular (for futur extentions as TSOP adapters for raw NOR/nand... maybe)

So I designed, built and tested a prototype since a couple of months with very good results.

Some pictures:

Naked PCB:

PCB equiped:

With Teensy and 360 clip boards :

Usage on NOR with SCSI 50 pins cable :

For those who are interested, here the gerber files to manufacture this board: TEENSY2PS3_v1.00
I'll post a "user manual" later (I have to translate it :p)

Meantime, I developed a new version (v1.01) with some minor improvements and the addition of optionnal "POWER LED" and "TRISTATE LED":

Build in process...
​

Official thread (french): TEENSY2PS3 : un "linker" Teensy++2.0 -> PS3 NOR et NAND - Jailbreak et hack par dongle USB - LS forums
​

gerber files to manufacture this board:
TEENSY2PS3_v1.00

Source: psx-place / Official Thread: Logic-Sunrise
Checkout the Downgrade Section in the PSX-Place.com Forums ---> Link​

 

What's that? And did I miss the link as I don't see an update.

About the v1.01 gerber files? See the previous posts in this thread.
http://www.psx-place.com/threads/teensy2ps3-pcb-linker-teensy-2-0-ps3.1728/

 

I was just looking on:

http://www.psdevwiki.com/ps3/Teensy++_2.0

And it says that the 1.27mm e4 & e5 are only required for NOR, but the teensy2ps3 v1.1 manual just says they are required. Is it safe to skip them if I'm just using this for NAND for now? The pcb they have on there that just does NAND, doesn't have them connected.

 

Yes you can skip e4 and e5 if you only use it for nand.

 

Yes you can skip e4 and e5 if you only use it for nand.

sir is this TSOP Nor Clip 56pin Compatible with TEENSY2PS3
http://store.logic-sunrise.com/fr/outils-flash-ps3-downgrade-jailbreak/941-tsop-nor-clip-56-pin.html

 

Pin layout look like standard one. So yes, is compatible.

 

Pin layout look like standard one. So yes, is compatible.

kozarovv can u see this list i preapare it for the whole matierls for TEENSY2PS3 nad can u pm me

Yes you can skip e4 and e5 if you only use it for nand.

littlebalup see this list and tell me its enough or noo

 

kozarovv can u see this list i preapare it for the whole matierls for TEENSY2PS3 nad can u pm me


littlebalup see this list and tell me its enough or noo

i buy those