Yugonibblit
PSX-Place Supporter
PS3 Love for Pictures of Teensy2ps3 DG tool
- Thread starter Yugonibblit
- Start date
kozarovv
Developer
That "yellow" one looks like a old (80-90s) Russian electronic hardware.Hello here are some pics of my DG harware!
Then every pcb was colored like that.
Yugonibblit
PSX-Place Supporter
kozarovv
Developer
Is cool as hardware, but looks ugly.
Yugonibblit
PSX-Place Supporter
Lol. Yeah your right
Strict_NATtype
Forum Noob
They look lovely. How much for one of those? a complete set, for NAND and NOR. Would love one for NAND. I like the Soviet looking one w/ yellow. Do you have one of those flashers where you mount the NAND chip? I've been looking for one of those or to build one for myself, but have no idea where or how.
Hello here are some pics of my DG hardware!
I just love littlebalup's pcb design!
If you want to order a board/boards to be made (it's easy to order online & not very dear..), use the Teensy2ps3 pcb gerber files archive from:
http://www.mediafire.com/download/fd8zqt1aykfi58p/TEENSY2PS3_v1.01.zip
And the Teensy2ps3 manual can be downloaded from:
http://www.mediafire.com/view/vg7410g3vo9w3dt/TEENSY2PS3_v1.01_manual_EN.pdf
Otherwise you can buy a board on ebay from 2 European sellers but you may not get the board colour you want.
The Teensy & Nand/NOR clips have to be bought separately. If you wanna avoid buying a clone, I suggest your order your Teensy from pjrc.
https://www.pjrc.com/teensy/
I don't know any shop/seller offering a kit.
Last edited:
Louay
Senior Member
@Yugonibblit How did you manage to solder those E4 & E5 while it small point the 2 pin header female to pcb and 2 pin header male to teensy thete is a person who tell me to solder 2 wires like those of ps2 modchip
Attachments
Yugonibblit
PSX-Place Supporter
@Louay, hello buddy those header pins i made my self by hand with a little effort you could do the same it wasnt easy,you can also buy the headers and pins but are hard to find,you could also use wires,i did mine that way because i wanted to.again it was not easy you have to file holes a little bit and the pins are a pain to solder just think your working on your DICK and you dont want to cut it off...LOL
Louay
Senior Member
@Yugonibblit do you have an idea about soldering DIP Switch to teensy2ps3 pcb for nand instead of jumper like this one posted in the website by @Turranius the 3 photos teensy.jpg are thr one posted by Turranuis in this website and the rest green pcb are my photo
Attachments
Last edited:
Yugonibblit
PSX-Place Supporter
NICE WORK SO FAR!, dip switches are not needed but is nice feature, i also have dip switches but i never took the time to solder them on,the dip switches i have are a bit smaller and are used in tyco train sets. these to will take some thinking and fabrication skills to solder,those red dip switches have long wires on the bottom of them shouldnt be to hard if you get those red ones, when i find the ones i have i will send you a pic of the dip switches i was going to use,but u should be fine with the ones in the pics you sent.
Yugonibblit
PSX-Place Supporter
NICE WORK SO FAR!, dip switches are not needed but is nice feature, i also have dip switches but i never took the time to solder them on,the dip switches i have are a bit smaller and are used in tyco train sets. these to will take some thinking and fabrication skills to solder,those red dip switches have long wires on the bottom of them shouldnt be to hard if you get those red ones, when i find the ones i have i will send you a pic of the dip switches i was going to use,but u should be fine with the ones in the pics you sent.
Yugonibblit
PSX-Place Supporter
looks like you could bend them to fit
Louay
Senior Member
I can bend them but pin height are tiny so after bending its like the switch will have no legs cause pins will be in bottom diretly just like this
Attachments
Yugonibblit
PSX-Place Supporter
Yeah the combination of switches you have make it a little tougher. you could maybe use 90 degree header pins.then solder switches to them?
