PS3 PS3 Super slim Unbrick help me

D

Dheeraj Gumber

Forum Noob
Hello Guys I have a PS3 superslim CECH 4208C. Last days I Brick my PS3 when I use PS3exploit. I am a noob in this field I have not any backup file.
I have a question
Can I use E3 Flasher to unbrick PS3 super slim

If yes so please guys tell Me Full process because I have not any experience of this .

And soory for bad English.

And thank you in advance
 
Thanks for reply.
I have any another question
How to tristate PS3 super slim this is the picture of my motherboard

Can you please tell me
 

Attachments

  • IMG_20191211_103907_922.jpg
    IMG_20191211_103907_922.jpg
    2.3 MB · Views: 220
Hello @sandungas I buy a new e3flasher now
I get dump from e3flasher and I check it with dump checker and it say OK Then I patch coreosofw4.85.bin.then I check my dump and it okay then I byte reverse my dump and put it on SD card and flash it. After flash I on PS3 the machine is on and green light show but on TV there is only black screen .Can you tell me where I make a mistake .I also tell you that before brick my PS3 I am on hfw4.84 .Please help me to solve this problem
 
Last edited:
Dheeraj Gumber said:
Hello @sandungas I buy a new e3flasher now
I get dump from e3flasher and I check it with dump checker and it say OK Then I patch coreosofw4.85.bin.then I check my dump and it okay then I byte reverse my dump and put it on SD card and flash it. After flash I on PS3 the machine is on and green light show but on TV there is only black screen .Can you tell me where I make a mistake .I also tell you that before brick my PS3 I am on hfw4.84 .Please help me to solve this problem
Click to expand...
Do you have the tristate wire connected ?
Im asking because is needed to remove it to allow the PS3 to boot normally, othreway if you try to boot the PS3 with the tristate wire connected is going to stay inactive in a black screen

You should ask for more help in the threads i mentioned, there is people posting in them with a lot more experience about this unbricking procedures than me
 
But after flash I unconnected the tristate wire I read the all thread you mention but this thread not help me I know only you help me
 
sandungas said:
Do you have the tristate wire connected ?
Im asking because is needed to remove it to allow the PS3 to boot normally, othreway if you try to boot the PS3 with the tristate wire connected is going to stay inactive in a black screen

You should ask for more help in the threads i mentioned, there is people posting in them with a lot more experience about this unbricking procedures than me
Click to expand...

Hey bro I flash my PS3 with E3 flasher but after flash TV show no signal but the PS3 is on can you please tell me where I make a mistake
 
Dheeraj Gumber said:
Hello @sandungas I buy a new e3flasher now
I get dump from e3flasher and I check it with dump checker and it say OK Then I patch coreosofw4.85.bin.then I check my dump and it okay then I byte reverse my dump and put it on SD card and flash it. After flash I on PS3 the machine is on and green light show but on TV there is only black screen .Can you tell me where I make a mistake .I also tell you that before brick my PS3 I am on hfw4.84 .Please help me to solve this problem
Click to expand...
I see you saying you byte reversed the dump before flashing it back. Had you reversed it before that?
Something else if you're on 4.84 use the 4.84 coreos.
 
Thanks for quick reply
@pink1 I tell you all steps that I do
First I make a dump with e3 flasher and after I patch 4.84 coreos and after I byte reversed the patched dump and after rename it and put in the SD card and flash it with e3 flasher and after flash I on the PS3 and machine is on but TV show no signal thats my problem please help me how can I solve this and save my PS3
 
Dheeraj Gumber said:
Thanks for quick reply
@pink1 I tell you all steps that I do
First I make a dump with e3 flasher and after I patch 4.84 coreos and after I byte reversed the patched dump and after rename it and put in the SD card and flash it with e3 flasher and after flash I on the PS3 and machine is on but TV show no signal thats my problem please help me how can I solve this and save my PS3
Click to expand...
You shouldn't need to byte reverse your bump before flashing it back unless you already byte reversed it or if it's a software dump.

Dumps made with the e3 are already byte reversed so if you byte reverse it then it's a normal dump. If you flash a normal dump using an e3 you get problems.
 
pink1 said:
You shouldn't need to byte reverse your bump before flashing it back unless you already byte reversed it or if it's a software dump.

Dumps made with the e3 are already byte reversed so if you byte reverse it then it's a normal dump. If you flash a normal dump using an e3 you get problems.
Click to expand...
OK thanks I try tommarow and give report to you if this work
 
Hello @pink1 I mistakely Damaged my E3 clip cable from middle .have you any solution to repair this because due to lockdown I cannot buy a new one I attached the photo of Damaged E3 clip cable and thanks in advance
 

Attachments

  • IMG_20200313_181301_533.jpg
    IMG_20200313_181301_533.jpg
    4.8 MB · Views: 56
  • IMG_20200117_172548_056.jpg
    IMG_20200117_172548_056.jpg
    1.6 MB · Views: 60
Dheeraj Gumber said:
Hello @pink1 I mistakely Damaged my E3 clip cable from middle .have you any solution to repair this because due to lockdown I cannot buy a new one I attached the photo of Damaged E3 clip cable and thanks in advance
Click to expand...
Unfortunatelly there is no way to fix it, sometimes the flat cables can be fixed in a cheap way by cutting them and peeling the tips (so they becomes shorter), but cutting the E3 flat cable is not going to work because the lines are tiny, is not posible to solder in it either, so i dont see any way to fix it
 
Did you get the e3 linker with your kit? Use that instead of the clip. Not sure if there is a proper pinout for your ps3 though. I know @littlebalup was working on it some time ago.
 
sandungas said:
Do you have the tristate wire connected ?
Im asking because is needed to remove it to allow the PS3 to boot normally, othreway if you try to boot the PS3 with the tristate wire connected is going to stay inactive in a black screen

You should ask for more help in the threads i mentioned, there is people posting in them with a lot more experience about this unbricking procedures than me
Click to expand...


is unbricking ps3 super slim possible
 
You must log in or register to reply here.

Similar threads

Back
Top