Stuck in "system cannot run correctly"

R

Ramzh

Hi, I bought a E3 Flasher recently to downgrade a PS3 Slim that I had at home but without HDD, so i got a new one 120GB NTFS, then I flashed the dump pacthed and now Im stuck on a balck screen with saying that my system does not run corrently. So i pressed start and select to update my firmware (it asks to use a 3.55 or higher) I tried with the OFW 3.55, a 4.75 HABIB, Roger 3.55 Downgrader, Rebug 3.55 Downgrader, HABIB 3.55 Downgrader, change USB Drive but all of them give me tha same error: 8002F2C5/8002FB5. I cannot go in FSM as I dont own a dongle unfortunatly...
 
Ramzh said:
Hi, I bought a E3 Flasher recently to downgrade a PS3 Slim that I had at home but without HDD, so i got a new one 120GB NTFS, then I flashed the dump pacthed and now Im stuck on a balck screen with saying that my system does not run corrently. So i pressed start and select to update my firmware (it asks to use a 3.55 or higher) I tried with the OFW 3.55, a 4.75 HABIB, Roger 3.55 Downgrader, Rebug 3.55 Downgrader, HABIB 3.55 Downgrader, change USB Drive but all of them give me tha same error: 8002F2C5/8002FB5. I cannot go in FSM as I dont own a dongle unfortunatly...
Click to expand...

Make sure to plug your BD Drive I assume you have CECH-2001 or 2101 model.

after then try this one http://www.mediafire.com/view/8ymhpfa338ylv6s/REBUG_3.55_3_999_DGR_PS3UPDAT.PUP
 
Ramzh said:
I have a 2003A
BD Drive seems connected and I tried the firmware you gave me but still gives me "data is corrupted. 8002F2C5"
Click to expand...

Ok, make sure to double check your BD-ROM, and I need you to verify a few things.

1. what version of OFW was it on before you flashed?
2. what did you use to patch your dump
3. Is it still asking you to install FW higher than 3.55?
4. Send me your dump via PM then I'll verify your dump
 
Now I can updated without any error, however after the PS3 finishs to prepare the update (100%), it's stucks there forever
 
After I format the HDD in FAT32, the PS3 finishes its process to prepare the update, but when it restarts it boots again to the black screen and ask me to press PS and install 3.55 or higher again
 
Ramzh said:
After I format the HDD in FAT32, the PS3 finishes its process to prepare the update, but when it restarts it boots again to the black screen and ask me to press PS and install 3.55 or higher again
Click to expand...

Try installing different 3.55 CFWs for ex) Rogero 3.55 3.7A, REBUG 3.55.4 or Kmeaw 3.55 you have to have successful 3.55 Installation at least once.
 
You have luck that your dump was fixable. Everywhere is writen check dump, and make 3 same dumps.... If your clip (you using clip, right?) was not seated good when you dumping flash. Then is bad also when you writing flash and probably you got error in writen dump. To check that i'm right dump now you flash and compare md5 with this from Joonie. If checksum is different then is clip problem.
 
Joonie said:
Try installing different 3.55 CFWs for ex) Rogero 3.55 3.7A, REBUG 3.55.4 or Kmeaw 3.55 you have to have successful 3.55 Installation at least once.
Click to expand...

I tried:
HABIB 3.55
KMEAW
REBUG 3.55
ROGERO 3.55
REBUG DOWNGRADER
ROGERO DOWNGRADER

but none of the worked, still rebooting into black screen asking to update 3.55 or higher

You have luck that your dump was fixable. Everywhere is writen check dump, and make 3 same dumps.... If your clip (you using clip, right?) was not seated good when you dumping flash. Then is bad also when you writing flash and probably you got error in writen dump. To check that i'm right dump now you flash and compare md5 with this from Joonie. If checksum is different then is clip problem.

kozarovv said:
You have luck that your dump was fixable. Everywhere is writen check dump, and make 3 same dumps.... If your clip (you using clip, right?) was not seated good when you dumping flash. Then is bad also when you writing flash and probably you got error in writen dump. To check that i'm right dump now you flash and compare md5 with this from Joonie. If checksum is different then is clip problem.
Click to expand...

I had 3 backup, checked them with PS3 NOR CHECKER and gave me OK to all of them so I went ahead
Im glad my dump was fixable, I really appreciated what Joonie did.
 
Ramzh said:
I tried:
HABIB 3.55
KMEAW
REBUG 3.55
ROGERO 3.55
REBUG DOWNGRADER
ROGERO DOWNGRADER

but none of the worked, still rebooting into black screen asking to update 3.55 or higher

You have luck that your dump was fixable. Everywhere is writen check dump, and make 3 same dumps.... If your clip (you using clip, right?) was not seated good when you dumping flash. Then is bad also when you writing flash and probably you got error in writen dump. To check that i'm right dump now you flash and compare md5 with this from Joonie. If checksum is different then is clip problem.



I had 3 backup, checked them with PS3 NOR CHECKER and gave me OK to all of them so I went ahead
Im glad my dump was fixable, I really appreciated what Joonie did.
Click to expand...

That's really really weird.. OK, try these now.

1. Try installing this one
http://www.mediafire.com/view/n0ajg85z94lzfik/RBG999NOBD_3.55.3.PUP

2. if .1 fails, try installing the latest OFW 4.75, then backup the dump again please.

3. if .2 fails. I'll send you a new dump, I have an idea.
 
Last edited:
EDIT :)

trvk_pkg0/1 contents seem corrupted, going to patch these two now

Ramzh said:
Nothing happes still the same
Click to expand...

OK, I'm going to patch trvk_prg0/prg1 and trvk_pkg0/trvk_pkg1 on your dump

for some reason, your original dump had 3.55 ones, I'm going to replace those with REBUG ones and then will send you the link of the patched dump.
 
Last edited:
Joonie said:
OK, I'm going to patch trvk_prg0/prg1 and trvk_pkg0/trvk_pkg1 on your dump

for some reason, your original dump had 3.55 ones, I'm going to replace those with REBUG ones and then will send you the link of the patched dump.
Click to expand...

Thanks really appreciate what you are doing
 
Ramzh said:
I tired what you said in PM, but still the same still reboot and asking for 3.55 or higher... Damn i am desperate
Click to expand...

I have no clue about what to do next,,

1. try using different HDD

2. get yourself a jig device [for FSM].
 
You must log in or register to reply here.

Similar threads

Back
Top