PS3 Fault finding YLOD with the SYSCON - First steps and Error reporting
Ganjo
Member
TOKINs are rated at 1000 hours @ 80C IIRC but they last longer. One of the last consoles I fixed was like 770 Days played and the TOKINs were working fine. Ive also had consoles that had less than 20 days and some of them were bad. If you do you need to make sure they use good low ESR tantalum caps.
Hello, all.
I've got a (probably) dying PS3 on my hands. Launch-day slim (2001A). Recently got it hooked back up after it spent a few years in a storage locker, and as of a couple weeks ago (after the first time I used it for a long gaming session, not just as a cd/dvd/bd player) nearly every boot attempt gives the triple-beep and flashing red light of death. However, it has almost always booted and run stably after a second power toggle. Which started me down the rabbit hole of diagnosis, which ended here.
Since it does run fine once started (so far), I was able to check ps3toolset via the console browser (and hot damn is that ever an impressive tool!). Each and every failure was listed 0xA0093004. As best I can tell that's an error in the RSX chip or its power supply/regulation, probably in the RSX's associated capacitors? It's not a total failure (yet) since it still boots with some persistence and runs stably while on (for now).
Unfortunately I don't have the tools or experience to do very much about it myself, depending on what's wrong with it. So I guess I'm mostly just asking to see if I understand my situation correctly?
Well, that and to ask: what I should do if I still want a working PS3 in the year 2024?
I've re-entered some of my ps3toolset.com output below:
I've got a (probably) dying PS3 on my hands. Launch-day slim (2001A). Recently got it hooked back up after it spent a few years in a storage locker, and as of a couple weeks ago (after the first time I used it for a long gaming session, not just as a cd/dvd/bd player) nearly every boot attempt gives the triple-beep and flashing red light of death. However, it has almost always booted and run stably after a second power toggle. Which started me down the rabbit hole of diagnosis, which ended here.
Since it does run fine once started (so far), I was able to check ps3toolset via the console browser (and hot damn is that ever an impressive tool!). Each and every failure was listed 0xA0093004. As best I can tell that's an error in the RSX chip or its power supply/regulation, probably in the RSX's associated capacitors? It's not a total failure (yet) since it still boots with some persistence and runs stably while on (for now).
Unfortunately I don't have the tools or experience to do very much about it myself, depending on what's wrong with it. So I guess I'm mostly just asking to see if I understand my situation correctly?
Well, that and to ask: what I should do if I still want a working PS3 in the year 2024?
I've re-entered some of my ps3toolset.com output below:
Code:
Firmware Version: 4.91 build 50754
Platform ID: CokG11
Board ID: DYN-001
Product Code: 84
Product SubCode: 0009
Hardare Config: 4E00FFFF0203BC3C
Syscon Firmware Version 832.00010002083E0832 (EEPROM: 00010002083E0832)
Statistics: Boot count 4619 - Shutdown Count 4593 - Runtime 401d 17h 58m 40s
...
Error 0: 0xA0093004 Time: Fri, 23 Aug 2024 20:57:55 GMT
... etc (1-31, same code)
OneFix
Member
Fixed by swapping 40nm RSX.
2teikitizi
Forum Noob
Hello!
I'm troubleshooting a PS3 FAT CECHL04, Version 1 MB, Sherwood SysCon. Never before opened and without any obvious sign of physical abuse, other than coated in dust. It just beeps 3 times after power on, shutting down immediately after.
I got the following error logs:
I'm OK with swapping components and getting this far connecting to the console, but it is my first shot at a faulty console, so I'd appreciate any pointers to troubleshooting it.
Thanks in advance.
I'm troubleshooting a PS3 FAT CECHL04, Version 1 MB, Sherwood SysCon. Never before opened and without any obvious sign of physical abuse, other than coated in dust. It just beeps 3 times after power on, shutting down immediately after.
I got the following error logs:
Code:
Press Ctrl+C to exit
>$ ERRLOG GET 00
ERRLOG GET 01
ERRLOG GET 02
ERRLOG GET 03
ERRLOG GET 04
ERRLOG GET 05
ERRLOG GET 06
ERRLOG GET 07
ERRLOG GET 08
ERRLOG GET 09
ERRLOG GET 0A
ERRLOG GET 0B
ERRLOG GET 0C
ERRLOG GET 0D
ERRLOG GET 0E
ERRLOG GET 0F
ERRLOG GET 10
ERRLOG GET 11
ERRLOG GET 12
ERRLOG GET 13
ERRLOG GET 14
ERRLOG GET 15
ERRLOG GET 16
ERRLOG GET 17
ERRLOG GET 18
ERRLOG GET 19
ERRLOG GET 1A
ERRLOG GET 1B
ERRLOG GET 1C
ERRLOG GET 1D
ERRLOG GET 1E
ERRLOG GET 1F00000000 A0093004 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0093004 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0093004 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0093004 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0093004 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0093004 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0093004 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0092114 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0091002 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0092114 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0091002 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0092114 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0091002 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0092114 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0091002 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0092114 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0091002 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0092114 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0091002 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0092114 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0091002 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0092114 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0091002 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0092114 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0091002 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0092114 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 A0091002 FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 FFFFFFFF FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 FFFFFFFF FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 FFFFFFFF FFFFFFFF
Press Ctrl+C to exit
>$ 00000000 FFFFFFFF FFFFFFFF
Press Ctrl+C to exit
>$ shutdown
00000000
# [SSM] Clearfatal Start.
# [SSM] Clearfatal ok.
# (PowerOff State)
Press Ctrl+C to exit
>$ powersw
00000000
# [SSM] Bringup Start.
OK 00000000
# [PowSeq] Error:A103
# [SSM] PS0 ng.
# [SSM] Cond/Fatal received, msg=24D0.
# [SSM] Fataldown Start.
Press Ctrl+C to exitI'm OK with swapping components and getting this far connecting to the console, but it is my first shot at a faulty console, so I'd appreciate any pointers to troubleshooting it.
Thanks in advance.
Hi guys, I have a CECH Q00 (DIA-001, they are NOT VER-001 like some say, so 90nm RSX) YLOD. Sometimes 3 seconds, sometimes longer. It seems to be going into recovery mode by itself on the longer ones. No obvious signs of damage. Warranty seal was void however, original Sony thermal paste was present. Seems like the system was last used in 2010, which is crazy being a 2009 system with 314 days LOL
Error log is as follows: Im assuming this is NEC Tokins but would appreciate a 2nd opinion
Error log is as follows: Im assuming this is NEC Tokins but would appreciate a 2nd opinion
Code:
ofst[ 36]:err_code:0xffffffff, clock:0x132a378a 2010/03/10 10:57:14
ofst[ 40]:err_code:0xa0802022, clock:0x132a3faa 2010/03/10 11:31:54
ofst[ 44]:err_code:0xa0802022, clock:0x132a44cd 2010/03/10 11:53:49
ofst[ 48]:err_code:0xa0802022, clock:0x132f2fe0 2010/03/14 05:25:52
ofst[ 52]:err_code:0xa0802022, clock:0x132f3076 2010/03/14 05:28:22
ofst[ 56]:err_code:0xa0802022, clock:0x13487bd9 2010/04/02 09:56:41
ofst[ 60]:err_code:0xa0802022, clock:0x13487d6e 2010/04/02 10:03:26
ofst[ 64]:err_code:0xa0801002, clock:0x2e1148a0 2024/06/28 10:10:40
ofst[ 68]:err_code:0xa0801002, clock:0x2e1148b3 2024/06/28 10:10:59
ofst[ 72]:err_code:0xa0801002, clock:0x2e114910 2024/06/28 10:12:32
ofst[ 76]:err_code:0xa0801002, clock:0x2e2685f3 2024/07/14 12:49:55
ofst[ 80]:err_code:0xa0801002, clock:0x2e26860d 2024/07/14 12:50:21
ofst[ 84]:err_code:0xa0801002, clock:0x2e26863d 2024/07/14 12:51:09
ofst[ 88]:err_code:0xa0801002, clock:0x2e2818b6 2024/07/15 17:28:22
ofst[ 92]:err_code:0xa0801002, clock:0x2e4fc52b 2024/08/14 19:42:35
ofst[ 96]:err_code:0xa0801002, clock:0x2e6372c2 2024/08/29 17:56:18
ofst[100]:err_code:0xa0801002, clock:0x2e6372e1 2024/08/29 17:56:49
ofst[104]:err_code:0xa0801002, clock:0x2e63731b 2024/08/29 17:57:47
ofst[108]:err_code:0xa0801002, clock:0x2e637325 2024/08/29 17:57:57
ofst[112]:err_code:0xa0001004, clock:0x2e637570 2024/08/29 18:07:44
ofst[116]:err_code:0xa0801002, clock:0x2e63757c 2024/08/29 18:07:56
ofst[120]:err_code:0xa0801002, clock:0x2e63758a 2024/08/29 18:08:10
ofst[124]:err_code:0xa0801002, clock:0x2e637591 2024/08/29 18:08:17
ofst[ 0]:err_code:0xa0801002, clock:0x2e637598 2024/08/29 18:08:24
ofst[ 4]:err_code:0xa0801002, clock:0x2e6375b0 2024/08/29 18:08:48
ofst[ 8]:err_code:0xa0801002, clock:0x2e6375c9 2024/08/29 18:09:13
ofst[ 12]:err_code:0xa0801002, clock:0x2e6375fc 2024/08/29 18:10:04
ofst[ 16]:err_code:0xa0801002, clock:0x2e63763e 2024/08/29 18:11:10
ofst[ 20]:err_code:0xa0801002, clock:0x2e6376ab 2024/08/29 18:12:59
ofst[ 24]:err_code:0xa0801002, clock:0x2e66391c 2024/08/31 20:27:08
ofst[ 28]:err_code:0xa0801002, clock:0x2e66393a 2024/08/31 20:27:38
ofst[ 32]:err_code:0xa0801002, clock:0x2e6651d5 2024/08/31 22:12:37
>$ becount
becount
Bringup : 710 times
Shutdown: 689 times
Power-on: 314day 04hour 06min 31secI've been having an issue where my PS3 Slim (CECH-2003A) will (most of the time) YLOD upon power-on. I have to spend about 20 minutes powering the thing on just to get to the safe mode menu. After waiting some time I can then reboot into the XMB. The PS3 stays stable on the XMB but will eventually YLOD when playing a game. The time it takes to YLOD in a game usually depends on how intensive the game is to run.
Because my PS3 does power on, I can dump the SYSCON log straight from the console.
What I find weird is that all of these logs seem to be from 2019, which is before I even owned this console. I've made sure that the date and time on my console are correct but no logs from 2024 show up.
SYSCON error log dump is from today. PS3 is running Evilnat's 4.91 beta 8 firmware but this issue still occurs on other firmwares so I don't think its a firmware issue.
Because my PS3 does power on, I can dump the SYSCON log straight from the console.
What I find weird is that all of these logs seem to be from 2019, which is before I even owned this console. I've made sure that the date and time on my console are correct but no logs from 2024 show up.
SYSCON error log dump is from today. PS3 is running Evilnat's 4.91 beta 8 firmware but this issue still occurs on other firmwares so I don't think its a firmware issue.
Code:
Firmware Version: 4.91 (build 50754)
Platform ID: CokG11
Product Code: 00 87
Product Sub Code: 00 09
Hardware Config: 000000000203BC3C
Syscon Firmware Version: 0832.00000000083E0832 (EEPROM: 00000000083E0832)
Bringup Count: 6752, Shutdown Count: 6564
Runtime: 484 Days, 17 Hours, 50 Minutes, 27 Seconds
Error Log
01: A0801002 Fri Nov 1 02:41:26 2019
02: A0801002 Fri Nov 1 01:42:22 2019
03: A0801002 Fri Nov 1 01:42:08 2019
04: A0801002 Fri Nov 1 01:41:57 2019
05: A0801002 Fri Nov 1 01:41:46 2019
06: A0801002 Fri Nov 1 01:41:36 2019
07: A0801002 Fri Nov 1 01:41:27 2019
08: A0801002 Fri Nov 1 01:41:15 2019
09: A0801002 Fri Nov 1 01:41:04 2019
10: A0801002 Fri Nov 1 01:40:54 2019
11: A0801002 Fri Nov 1 01:40:44 2019
12: A0801002 Fri Nov 1 01:40:34 2019
13: A0801002 Fri Nov 1 01:40:12 2019
14: A0801002 Fri Nov 1 01:39:59 2019
15: A0801002 Fri Nov 1 01:39:42 2019
16: A0801002 Fri Nov 1 01:39:11 2019
17: A0801002 Fri Nov 1 01:38:59 2019
18: A0801002 Fri Nov 1 01:38:47 2019
19: A0801002 Fri Nov 1 01:38:35 2019
20: A0801002 Fri Nov 1 01:38:23 2019
21: A0801002 Fri Nov 1 01:38:11 2019
22: A0801002 Fri Nov 1 01:38:00 2019
23: A0801002 Fri Nov 1 01:37:48 2019
24: A0801002 Fri Nov 1 01:37:38 2019
25: A0801002 Fri Nov 1 01:37:26 2019
26: A0801002 Fri Nov 1 01:37:14 2019
27: A0801002 Fri Nov 1 01:37:03 2019
28: A0801002 Fri Nov 1 01:36:52 2019
29: A0801002 Fri Nov 1 01:36:40 2019
30: A0801002 Fri Nov 1 01:36:30 2019
31: A0801002 Fri Nov 1 01:36:18 2019
32: FFFFFFFF Fri Dec 31 23:59:59 1999Ganjo
Member
Bad RSX TOKINs. Yours will probably need all 4 replaced
Ganjo
Member
RSX TOKINs
Ganjo
Member
RSX TOKINs
Help please!
I have a CECH2001A that turns on and beep 3 times then turns off and blinking red light. This unit has been in a repair shop that my friend brought for a repair and ended up nothing has been fix. It was almost a year to that shop hehehe and this is what i got after diagnosing.. A capacitor has been crack open on the front side after I remove the capacitor I put back the ps3 and apply a new thermal paste. The 3 beeps and the blinking red lights gone. The unit turns on the fan is spinning , power led is green but has no display leave the unit turned on for an a hour still no display. The following day I tested the unit again and here comes the the 3 beeps again and turns off then red blinking light. Then I decided to read the syscon and this is what ive got.. Please help.
I have a CECH2001A that turns on and beep 3 times then turns off and blinking red light. This unit has been in a repair shop that my friend brought for a repair and ended up nothing has been fix. It was almost a year to that shop hehehe and this is what i got after diagnosing.. A capacitor has been crack open on the front side after I remove the capacitor I put back the ps3 and apply a new thermal paste. The 3 beeps and the blinking red lights gone. The unit turns on the fan is spinning , power led is green but has no display leave the unit turned on for an a hour still no display. The following day I tested the unit again and here comes the the 3 beeps again and turns off then red blinking light. Then I decided to read the syscon and this is what ive got.. Please help.
Code:
>$ shutdown
00000000
# [SSM] PS0 ok.
# [SSM] PS1 ok.
# [SSM] PS2 ok.
# [SSM] PS3 ok.
# [SSM] PS4 ok.
# (PowerOn State)
#!
#!Boot Loader SE Version 3.1.5
#!(Build ID: 3814,43498,
#!Build Date: 2009-12-01_21:11:40)
#!
#!Copyright(C) 2009 Sony Computer Entertainment Inc.All Rights Reserved.
#!
#![INFO]: Connecting to Debug Device (SB UART)
# [SSM] Cond/Fatal received, msg=2687.
# [SSM] Fataldown Start.
# [SSM] Fataldown ok.
# (PowerOff State) (Fatal)
# [SSM] Clearfatal Start.
# [SSM] Clearfatal ok.
# (PowerOff State)
Press Ctrl+C to exit
>$ errlog
00000000
# CODE CLOCK
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0801200 FFFFFFFF
# A0802024 FFFFFFFF
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0802024 FFFFFFFF
# A0902124 FFFFFFFF
# A0902024 FFFFFFFF
# A0902024 FFFFFFFF
# A0902024 FFFFFFFF
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0801200 FFFFFFFF
# A0802024 FFFFFFFF
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0802024 FFFFFFFF
# A0A02024 FFFFFFFF
# A0A02024 FFFFFFFF
# A0A02024 FFFFFFFF
# A0402024 FFFFFFFF
# A0402124 FFFFFFFF
# A0403034 FFFFFFFF
# A0404441 FFFFFFFF
# A0A02124 FFFFFFFF
# A0A02024 FFFFFFFF
# A0A02024 FFFFFFFF
# A0A02024 FFFFFFFF
# A0522124 FFFFFFFF
# A0523039 FFFFFFFFAttached image from the board some components are missing and no idea of their value..
Code:
>\$ shutdown
00000000
# [SSM] PS0 ok.
# [SSM] PS1 ok.
# [SSM] PS2 ok.
# [SSM] PS3 ok.
# [SSM] PS4 ok.
# (PowerOn State)
#!
#!Boot Loader SE Version 3.1.5
#!(Build ID: 3814,43498,
#!Build Date: 2009-12-01_21:11:40)
#!
#!Copyright(C) 2009 Sony Computer Entertainment Inc.All Rights Reserved.
#!
#![INFO]: Connecting to Debug Device (SB UART)
# [SSM] Cond/Fatal received, msg=2687.
# [SSM] Fataldown Start.
# [SSM] Fataldown ok.
# (PowerOff State) (Fatal)
# [SSM] Clearfatal Start.
# [SSM] Clearfatal ok.
# (PowerOff State)
Press Ctrl+C to exit
>$ errlog
00000000
# CODE CLOCK
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0801200 FFFFFFFF
# A0802024 FFFFFFFF
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0802024 FFFFFFFF
# A0902124 FFFFFFFF
# A0902024 FFFFFFFF
# A0902024 FFFFFFFF
# A0902024 FFFFFFFF
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0801200 FFFFFFFF
# A0802024 FFFFFFFF
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0802024 FFFFFFFF
# A0A02024 FFFFFFFF
# A0A02024 FFFFFFFF
# A0A02024 FFFFFFFF
# A0402024 FFFFFFFF
# A0402124 FFFFFFFF
# A0403034 FFFFFFFF
# A0404441 FFFFFFFF
# A0A02124 FFFFFFFF
# A0A02024 FFFFFFFF
# A0A02024 FFFFFFFF
# A0A02024 FFFFFFFF
# A0522124 FFFFFFFF
# A0523039 FFFFFFFF2teikitizi
Forum Noob
Thanks. Will update after replacement. All the best
100% Damage to the soldering of the video processor. Warming up or complete soldering can helpAttached image from the board some components are missing and no idea of their value..
Code:>\$ shutdown 00000000 # [SSM] PS0 ok. # [SSM] PS1 ok. # [SSM] PS2 ok. # [SSM] PS3 ok. # [SSM] PS4 ok. # (PowerOn State) #! #!Boot Loader SE Version 3.1.5 #!(Build ID: 3814,43498, #!Build Date: 2009-12-01_21:11:40) #! #!Copyright(C) 2009 Sony Computer Entertainment Inc.All Rights Reserved. #! #![INFO]: Connecting to Debug Device (SB UART) # [SSM] Cond/Fatal received, msg=2687. # [SSM] Fataldown Start. # [SSM] Fataldown ok. # (PowerOff State) (Fatal) # [SSM] Clearfatal Start. # [SSM] Clearfatal ok. # (PowerOff State) Press Ctrl+C to exit >$ errlog 00000000 # CODE CLOCK # A0802024 FFFFFFFF # A0802124 FFFFFFFF # A0801200 FFFFFFFF # A0802024 FFFFFFFF # A0802024 FFFFFFFF # A0802124 FFFFFFFF # A0802024 FFFFFFFF # A0902124 FFFFFFFF # A0902024 FFFFFFFF # A0902024 FFFFFFFF # A0902024 FFFFFFFF # A0802024 FFFFFFFF # A0802124 FFFFFFFF # A0801200 FFFFFFFF # A0802024 FFFFFFFF # A0802024 FFFFFFFF # A0802124 FFFFFFFF # A0802024 FFFFFFFF # A0A02024 FFFFFFFF # A0A02024 FFFFFFFF # A0A02024 FFFFFFFF # A0402024 FFFFFFFF # A0402124 FFFFFFFF # A0403034 FFFFFFFF # A0404441 FFFFFFFF # A0A02124 FFFFFFFF # A0A02024 FFFFFFFF # A0A02024 FFFFFFFF # A0A02024 FFFFFFFF # A0522124 FFFFFFFF # A0523039 FFFFFFFF
Hello thanks for the reply..
Furtherly i try to check the NEC Tokin near the RSX this is what I found. I think this is bad and needs to be replace with a tantalum cap right?
Привет, спасибо за ответ..
Далее я пытаюсь проверить NEC Tokin возле RSX, вот что я нашел. Я думаю, что это плохо и его нужно заменить на танталовый колпачок, верно?
[/ЦИТИРОВАТЬ]
NEC Токин
Менять не нужно
Francis023
Member
Error 1001, DYN-001 Sometimes booted the ylod after a minute, mostly YLOD any idea where to look for are big help thanks.
NEC Tokin CELL
PlayStation3 CECH2001A DYN-001 YLOD Problem found! HDMI Chip was the culprit..
I'm very thankful I have found this forum. All the information you need about YLOD Repair is here. You just have to be persistent on reading to be able to find a solution to YLOD problem of your ps3. Thank you very much to all the contributors to this forum for sharing your expertise.
Prior to this I already remove all 4 NEC Tokin and replace with tantalum capacitors.
these are the syscon error logs after removing the HDMI Chip.. No more 3 beeps before shutdown and blinking red.
Then test the PS3 sending syscon command bringup and leave the unit in the bringup mode for almost 1.5hrs and the unit is still working no more overheats the fan is spinning calmly. the tmp 0 and 1 is 58C/59C
Press Ctrl+C to exit
>$ powerstate
00000000
# [SSM] PS0 ok.
# [SSM] PS1 ok.
# [SSM] PS2 ok.
# [SSM] PS3 ok.
# [SSM] PS4 ok.
# (PowerOn State)
OK 00000000
#!
#!Boot Loader SE Version 3.1.5
#!(Build ID: 3814,43498,
#!Build Date: 2009-12-01_21:11:40)
#!
#!Copyright(C) 2009 Sony Computer Entertainment Inc.All Rights Reserved.
#!
#![INFO]: Connecting to Debug Device (SB UART)
# ATA :ON
# PCI :OFF
# PCIex:OFF
# RSX :ON
# GDDR :ON
# XDR :ON
# EURUS:ON
# SB :ON
# LAN :ON
# WLAN :ON
Press Ctrl+C to exit
A0802024, A0802124, or A0902124, A0902124 after removing HDMI Chip no other codes on the errlog except this 2024 / 2124.
>$ errlog
00000000
# CODE CLOCK
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0801200 FFFFFFFF
# A0802024 FFFFFFFF
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0802024 FFFFFFFF
# A0902124 FFFFFFFF
# A0902024 FFFFFFFF
# A0902024 FFFFFFFF
# A0902024 FFFFFFFF
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
ShoutOut! to this contributors. Your inputs on those pages on this thread that made me realize that the HDMI Chip is the problem. Thank You!
RIP-Felix sandungas vyktormvmpay25 marciolsf SkaziChris
I'm very thankful I have found this forum. All the information you need about YLOD Repair is here. You just have to be persistent on reading to be able to find a solution to YLOD problem of your ps3. Thank you very much to all the contributors to this forum for sharing your expertise.
Prior to this I already remove all 4 NEC Tokin and replace with tantalum capacitors.
these are the syscon error logs after removing the HDMI Chip.. No more 3 beeps before shutdown and blinking red.
Then test the PS3 sending syscon command bringup and leave the unit in the bringup mode for almost 1.5hrs and the unit is still working no more overheats the fan is spinning calmly. the tmp 0 and 1 is 58C/59C
Press Ctrl+C to exit
>$ powerstate
00000000
# [SSM] PS0 ok.
# [SSM] PS1 ok.
# [SSM] PS2 ok.
# [SSM] PS3 ok.
# [SSM] PS4 ok.
# (PowerOn State)
OK 00000000
#!
#!Boot Loader SE Version 3.1.5
#!(Build ID: 3814,43498,
#!Build Date: 2009-12-01_21:11:40)
#!
#!Copyright(C) 2009 Sony Computer Entertainment Inc.All Rights Reserved.
#!
#![INFO]: Connecting to Debug Device (SB UART)
# ATA :ON
# PCI :OFF
# PCIex:OFF
# RSX :ON
# GDDR :ON
# XDR :ON
# EURUS:ON
# SB :ON
# LAN :ON
# WLAN :ON
Press Ctrl+C to exit
A0802024, A0802124, or A0902124, A0902124 after removing HDMI Chip no other codes on the errlog except this 2024 / 2124.
>$ errlog
00000000
# CODE CLOCK
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0801200 FFFFFFFF
# A0802024 FFFFFFFF
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
# A0802024 FFFFFFFF
# A0902124 FFFFFFFF
# A0902024 FFFFFFFF
# A0902024 FFFFFFFF
# A0902024 FFFFFFFF
# A0802024 FFFFFFFF
# A0802124 FFFFFFFF
ShoutOut! to this contributors. Your inputs on those pages on this thread that made me realize that the HDMI Chip is the problem. Thank You!
RIP-Felix sandungas vyktormvmpay25 marciolsf SkaziChris
Ganjo
Member
Anyone have any suggestions for this one? Have an A01 that was opened but showed no signs of being worked on before. I thought it needed a CELL reballl but after doing a reball it still has A0233020, once it also had A0902120. I see no shorts or anything abnormal in the CELL power circuit. All fuses are good. PSU is good. Its only shown the 902120 error once in syscon but it always shows 233020
Code:
ofst[ 68]:err_code:0xffffffff, clock:0xffffffff
ofst[ 72]:err_code:0xa0801301, clock:0xffffffff
ofst[ 76]:err_code:0xa0233020, clock:0xffffffff
ofst[ 80]:err_code:0xa0233020, clock:0xffffffff
ofst[ 84]:err_code:0xa0801301, clock:0xffffffff
ofst[ 88]:err_code:0xa0902203, clock:0xffffffff
ofst[ 92]:err_code:0xa0233020, clock:0xffffffff
ofst[ 96]:err_code:0xa0902120, clock:0xffffffff
ofst[100]:err_code:0xa0233020, clock:0xffffffff
ofst[104]:err_code:0xa0902120, clock:0xffffffff
ofst[108]:err_code:0xa0233020, clock:0xffffffff
ofst[112]:err_code:0xa0233020, clock:0xffffffff
ofst[116]:err_code:0xa0233020, clock:0xffffffff
ofst[120]:err_code:0xa0801301, clock:0xffffffff
ofst[124]:err_code:0xa0801301, clock:0xffffffff
ofst[ 0]:err_code:0xa0233020, clock:0xffffffff
ofst[ 4]:err_code:0xa0233020, clock:0xffffffff
ofst[ 8]:err_code:0xa0801301, clock:0xffffffff
ofst[ 12]:err_code:0xa0233020, clock:0xffffffff
ofst[ 16]:err_code:0xa0233020, clock:0xffffffff
ofst[ 20]:err_code:0xa0233020, clock:0xffffffff
ofst[ 24]:err_code:0xa0233020, clock:0xffffffff
ofst[ 28]:err_code:0xa0801301, clock:0xffffffff
ofst[ 32]:err_code:0xa0801301, clock:0xffffffff
ofst[ 36]:err_code:0xa0233020, clock:0xffffffff
ofst[ 40]:err_code:0xa0233020, clock:0xffffffff
ofst[ 44]:err_code:0xa0233020, clock:0xffffffff
ofst[ 48]:err_code:0xa0233020, clock:0xffffffff
ofst[ 52]:err_code:0xa0233020, clock:0xffffffff
ofst[ 56]:err_code:0xa0233020, clock:0xffffffff
ofst[ 60]:err_code:0xa0801301, clock:0xffffffff
ofst[ 64]:err_code:0xa0233020, clock:0xffffffff
Bringup : 2452 times
Shutdown: 2417 times
Power-on: 256day 18hour 42min 26sec
[SSM] state: 0000 -> 0101
Bringup Mode #0 (0xFF)
[SSM] ssmCb_OnStartingBePowOn() called.
[SSM] First Boot.
[SSM] Bringup mode : syspm_stat=00000000/00000000
[POWSEQ] PowerSeq_Setup called.
[SSM] state: 0101 -> 0201
[POWSEQ] AV Backend Setup
[SSM] state: 0201 -> 0102
[SSM] state: 0102 -> 0202
[SSM] state: 0202 -> 0103
[SSM] state: 0103 -> 0303
[SSM] PowSeq Fail : Detected !
[SSM] state: 0303 -> 0700
[POWSEQ] AV Backend Letup
[SSM] Shutdown mode : syspm_stat=00000000/00000000
[ERROR]: 0xa0233020
NEW SYSCON ERRORS
ofst[ 0]:err_code:0xa0233020, clock:0xffffffff
ofst[ 4]:err_code:0xa0902120, clock:0xffffffffSimilar threads
-
-
PS3 CECHA00 with several SYSCON errors (3004, 1001,1002, 2120,3011)
- Started by LSL
- Replies: 7
-
PS3 Interesting PS3 Errors (1802, 1701, 1601) and Capacitor Replacement- Started by Cheshire UK
- Replies: 2
-