PS3 Fault finding YLOD with the SYSCON - First steps and Error reporting

[RIP-Felix]

HI, new to this syscon testing, but have a lots of PS3 boards home that I would like to bring back to life ...

The first test was on SEM-001 (first soldered the diag,and didn't get nothing) ...

So after removing DIAG pin got this result :

===================================
ERR 00: 00000000 A0022110 23815B98
ERR 01: 00000000 A0022110 23815B8F
ERR 02: 00000000 A0022110 217DE5EF
ERR 03: 00000000 A0022110 217DE5E7
ERR 04: 00000000 A0022110 213C0D11
ERR 05: 00000000 A0022110 213C0D08
ERR 06: 00000000 A0022110 213C0D01
ERR 07: 00000000 A0022110 20F72F67
ERR 08: 00000000 A0022110 20F72F64
ERR 09: 00000000 A0022110 20F72F26
ERR 10: 00000000 A0022110 20F0FA0A
ERR 11: 00000000 A0022110 20F0FA06
ERR 12: 00000000 A0022110 20F0F9FE
ERR 13: 00000000 A0022110 20F0F9F6
ERR 14: 00000000 A0022110 20F0E80C
ERR 15: 00000000 A0022110 20F0E7E6
ERR 16: 00000000 A0022110 20F0E7A8
ERR 17: 00000000 A0022110 20F0E790
ERR 18: 00000000 A0022110 20F0E77E
ERR 19: 00000000 A0801001 15713A43
===================================

As I read this is somthing with clock failture ... As a solve read here on pages to chech F6001, which is ok with multimeter ...

Can someone point me further wheare to check ...

THX

Did you check the wiki?

 

[nbdy]

Did you check the wiki?

OK, In wiki, after rereading, this should be nec tokin error the A0801001 ....

Now the question, I'm I only looking for the last error, or should I also take in question the errors before the last ???

Sorry new to this, but as I said have a lot boards left here by me that would be nice to fix and spend to some kids here in Croatia that they can play ... (for no cost, and have the time to fix) ....

 

[RIP-Felix]

error 00 is the latest. So the last error was 02 2110.

This error can be caused by a 5V_MISC short to ground. One user had an A0022110 after replacing IC6105 (Buck Converter) and accidentally bridging the 5V voltage input. So check the 5V line for shorts.
This error has been resolved by a number of users who had a short on F6001. It is important to note that something usually causes that fuse to blow, like a short. So it's important to troubleshoot the board to find and repair the shorting component before replacing the fuse. Otherwise the new one will blow too.

One user, who resolved this error on his C model PS3, noted "very short YLOD. Error code shows 2110[...]Some earlier code shows 1001 and 1002." The 1001 & 1002 errors he noted in the log before the 2110 appeared may have been a clue that C6019 or C6020 (as they are in parallel) was deteriorating. Further investigation is needed to confirm this hypothesis, however. In his case, C6019 was shorting and caused F6001 to blow. This short overloaded F6001 and cut power to many Subsystems, such as the HDD, USB ports, South bridge, CPU, GPU, etc. Another user confirmed this. The error log was showing code 2110 and one entry earlier was showing code 1001. Checking both capacitors after removing them from the board, confirmed that one capacitor was reading 140 ohms and not reading as a capacitor, so it was working as a resistor causing extra load in the fuse.

 

[Jeka88]

Hello everyone, please help me to deal with these errors

ERR 00: 00000000 A0203010 FFFFFFFF
ERR 01: 00000000 A0202120 FFFFFFFF
ERR 02: 00000000 A0202120 FFFFFFFF
ERR 03: 00000000 A0202120 FFFFFFFF
ERR 04: 00000000 A0202120 FFFFFFFF
ERR 05: 00000000 A0202120 FFFFFFFF
ERR 06: 00000000 A0202120 FFFFFFFF
ERR 07: 00000000 A0202120 FFFFFFFF
ERR 08: 00000000 A0202120 FFFFFFFF
ERR 09: 00000000 A0202120 FFFFFFFF
ERR 10: 00000000 A0202120 FFFFFFFF
ERR 11: 00000000 A0202120 FFFFFFFF
ERR 12: 00000000 A0202120 FFFFFFFF
ERR 13: 00000000 A0202120 FFFFFFFF
ERR 14: 00000000 A0202120 FFFFFFFF
ERR 15: 00000000 A0202120 FFFFFFFF
ERR 16: 00000000 A0203010 FFFFFFFF
ERR 17: 00000000 A0202120 FFFFFFFF
ERR 18: 00000000 A0202120 FFFFFFFF
ERR 19: 00000000 A0202120 FFFFFFFF
==================================
I replaced all Tokin and the errors did not change, the reflow did not help, replacing the rsx will help revive it?

 

[Jeka88]

[/url][/IMG]

Hello everyone, please help me to deal with these errors

ERR 00: 00000000 A0203010 FFFFFFFF
ERR 01: 00000000 A0202120 FFFFFFFF
ERR 02: 00000000 A0202120 FFFFFFFF
ERR 03: 00000000 A0202120 FFFFFFFF
ERR 04: 00000000 A0202120 FFFFFFFF
ERR 05: 00000000 A0202120 FFFFFFFF
ERR 06: 00000000 A0202120 FFFFFFFF
ERR 07: 00000000 A0202120 FFFFFFFF
ERR 08: 00000000 A0202120 FFFFFFFF
ERR 09: 00000000 A0202120 FFFFFFFF
ERR 10: 00000000 A0202120 FFFFFFFF
ERR 11: 00000000 A0202120 FFFFFFFF
ERR 12: 00000000 A0202120 FFFFFFFF
ERR 13: 00000000 A0202120 FFFFFFFF
ERR 14: 00000000 A0202120 FFFFFFFF
ERR 15: 00000000 A0202120 FFFFFFFF
ERR 16: 00000000 A0203010 FFFFFFFF
ERR 17: 00000000 A0202120 FFFFFFFF
ERR 18: 00000000 A0202120 FFFFFFFF
ERR 19: 00000000 A0202120 FFFFFFFF
==================================
I replaced all Tokin and the errors did not change, the reflow did not help, replacing the rsx will help revive it?

F6302 and C6320 are normal and all other fuses are also alive,but I noticed that the measurements do not match this photo MC2_VDDIO-0,3 ohm,VDDA-0,3 ohm

 

[DeadEnd]

[/url][/IMG]


F6302 and C6320 are normal and all other fuses are also alive,but I noticed that the measurements do not match this photo MC2_VDDIO-0,3 ohm,VDDA-0,3 ohm

I had this error when F6301 was blown.

 

[Bazilthemage45]

Hi to all, i am new to this community so sorry if that has been answered allready. I have 3 ps3s with YLOD issue that i got as a repair project, and without really knowing what i am doing i followed the tutorial to get the Errlog-bringup and becount results for all three. Can anyone enlighten me with any suggestions? How should i upload the syscon findings?

 

[Jeka88]

I had this error when F6301 was blown.

all fuses in my motherboard are good((

 

[nbdy]

error 00 is the latest. So the last error was 02 2110.

Downloaded all the shematics from your sig ...

SEM-001 board

The wiki says for this error : C6019 was shorting and caused F6001 to blow, where both are OK on my board, even the 6002,6301 and 6302 fuses are OK ...

Found 6019 which has 1.284 mF (like other on the board same dimensions) (measured onboard) ...

But can't find 6020 and the IC5001 ...

Could you detail me further ...

THX

 

[Bazilthemage45]

Can anyone suggest possible fixes for these errors:
(CECH-A model)
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0403034 FFFFFFFF

[SSM] state: 0000 -> 0101
Bringup Mode #0 (0xFF)
[SSM] ssmCb_OnStartingBePowOn() called.
[SSM] First Boot.
[SSM] Bringup mode : syspm_stat=00000000/00000000
[POWSEQ] PowerSeq_Setup called.
[SSM] state: 0101 -> 0201
[POWSEQ] AV Backend Setup
[SSM] state: 0201 -> 0102

 

[Bazilthemage45]

CECH-C

00000000 A0801200 FFFFFFFF
00000000 A0801200 FFFFFFFF
00000000 A0801200 FFFFFFFF
00000000 A0801802 0B4886A2
00000000 A0801802 0B488696
00000000 A0801601 0B4886CE
00000000 A0801701 0B4886CE
00000000 A0403034 0B4888BD
00000000 A0404402 0B4888BD
00000000 A0A02031 0B4888B6
00000000 A0A02031 0B4888AA
00000000 A0A02031 0B4888A1
00000000 A0403034 0B488886
00000000 A0404402 0B488886
00000000 A0A02031 0B488880
00000000 A0403034 0B488876
00000000 A0404402 0B488876
00000000 A0403034 0B4886EB
00000000 A0404402 0B4886EB
00000000 A0403034 0B4886CC
00000000 A0404402 0B4886CC
00000000 A0403034 0B4886BA
00000000 A0404402 0B4886BA
00000000 A0801601 0B4886A1
00000000 A0801701 0B4886A1
00000000 A0A02031 FFFFFFFF
00000000 A0801601 0B4896B1
00000000 A08014FF 0B4896B1
00000000 A0801701 0B4896B1
00000000 A0801601 0B4896A7
00000000 A08014FF 0B4896A7


bringup
[SSM] state: 0000 -> 0101
Bringup Mode #0 (0xFF)
[SSM] ssmCb_OnStartingBePowOn() called.
[SSM] First Boot.
[SSM] Bringup mode : syspm_stat=00000000/00000000
[POWSEQ] PowerSeq_Setup called.
[SSM] state: 0101 -> 0201
[POWSEQ] AV Backend Setup
[SSM] state: 0201 -> 0102
[SSM] state: 0102 -> 0202
[SSM] state: 0202 -> 0103
[SSM] state: 0103 -> 0203
[SSM] ssmCb_BeforeBeOn() called.
[SSM] state: 0203 -> 0104
Psbd_SbTransMode_Half:0x21e2
>$ becount
[SSM] state: 0104 -> 0204
[SSM] state: 0204 -> 0105
[SSM] state: 0105 -> 0400
(PowerOn State)
[SERV NVS] READ CMD
Boot Loader SE Version 1.5.0 (Build ID: 1798,18531, Build Data: 2007-01-10_12:09:26)
Copyright(C) 2006 Sony Computer Entertainment Inc.All Rights Reserved.
[SERV SETCFG] XDR (CH0,CH1) ASSERT
[SERV SETCFG] XDR (CH0,CH1) DEASSERT
[INFO]: Connecting to Debug Device (SB UART)
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV NVS] READ CMD
[SERV THERM] NOTIFY_MODE CMD
[WMZONE] *** Thermal Shutdown (1st BE Primary ) ***
[SERV THERM] Thermal Error Detected!
[SSM] *** Thermal Alert (ZONE) ***
[SSM] state: 0400 -> 0700
[POWSEQ] AV Backend Letup
[SSM] ssmCb_AfterBeOn() called.
[SSM] Shutdown mode : syspm_stat=00000000/00000000
[SERV THERM] *** NO COMMTAG SPECIFIED! ***
[ERR_PRINT] serv_secu.c, line 67
*** send error ***
[ERROR]: 0xa0801200
[POWSEQ] PowerSeq_Letup called.
[SSM] state: 0700 -> 0600
(PowerOff State) (Fatal)

 

[Bazilthemage45]

Another CECH-C

00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0404402 FFFFFFFF
00000000 A0403034 FFFFFFFF


bringup
[SSM] state: 0000 -> 0101
Bringup Mode #0 (0xFF)
[SSM] ssmCb_OnStartingBePowOn() called.
[SSM] First Boot.
[SSM] Bringup mode : syspm_stat=00000000/00000000
[POWSEQ] PowerSeq_Setup called.
[SSM] state: 0101 -> 0201
[POWSEQ] AV Backend Setup
[SSM] state: 0201 -> 0102
>$ bringup
[SSM] state: 0102 -> 0202
[SSM] state: 0202 -> 0103
[SSM] state: 0103 -> 0203
[SSM] ssmCb_BeforeBeOn() called.
[SSM] state: 0203 -> 0104
Psbd_SbTransMode_Half:0x21e2
[SSM] fatalreq delayed.
[ERROR]: 0xa0401001
PLL lock -> unlock
[SSM] *** NON-FATAL EVENT received while fataldown/fataloff, ignored. ***
[ERROR]: 0xa0401301
[POWERSEQ] Error : BitTraining RSX:RRAC:RX0:GLOBAL1:RX_STATUS
[SSM] state: 0104 -> 0304
[SSM] ssmCb_AfterBeOn2() called.
[SSM] *** Power Fail BE ***
[SSM] state: 0304 -> 0700
[POWSEQ] AV Backend Letup
[SSM] Shutdown mode : syspm_stat=00000000/00000000
[ERROR]: 0xa0404402
[ERROR]: 0xa0403034
[ERROR]: 0xa0902120
[POWSEQ] PowerSeq_Letup called.
[SSM] state: 0700 -> 0600
(PowerOff State) (Fatal)

 

[Timbo9876]

Can anyone suggest possible fixes for these errors:
(CECH-A model)
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0203010 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0403034 FFFFFFFF
00000000 A0403034 FFFFFFFF

[SSM] state: 0000 -> 0101
Bringup Mode #0 (0xFF)
[SSM] ssmCb_OnStartingBePowOn() called.
[SSM] First Boot.
[SSM] Bringup mode : syspm_stat=00000000/00000000
[POWSEQ] PowerSeq_Setup called.
[SSM] state: 0101 -> 0201
[POWSEQ] AV Backend Setup
[SSM] state: 0201 -> 0102

You might want to view my video concerning this error code.

 

[Bazilthemage45]

You might want to view my video concerning this error code.

The console arrived to me allready dellided (without any obvious visible harm) and with rather fresh paste applied. I did another repaste and tried it without any change. I wasn't so thorough, meaning didn't replace the thermal pads but that was before i dived in the syscon method. Should i try again, should i go straight to reflowing? I don't really care about the outcome since it's more of a hobby than business, but i am not comfortable yet with trying a full RSX reballing (nor do i have the equipment other than a cheap-chinese rework station). Should i just declare it dead and move on? From what i have been reading, 3034 errors is associated with GPU/CPU contact faults. Has anyone succeeded with less complicated methods?

 

[nbdy]

Sorry for not reading the tut to the end, tought that the error log is enugh ....

SEM-001

===================================
ERR 00: 00000000 A0022110 23815B98
ERR 01: 00000000 A0022110 23815B8F
ERR 02: 00000000 A0022110 217DE5EF
ERR 03: 00000000 A0022110 217DE5E7
ERR 04: 00000000 A0022110 213C0D11
ERR 05: 00000000 A0022110 213C0D08
ERR 06: 00000000 A0022110 213C0D01
ERR 07: 00000000 A0022110 20F72F67
ERR 08: 00000000 A0022110 20F72F64
ERR 09: 00000000 A0022110 20F72F26
ERR 10: 00000000 A0022110 20F0FA0A
ERR 11: 00000000 A0022110 20F0FA06
ERR 12: 00000000 A0022110 20F0F9FE
ERR 13: 00000000 A0022110 20F0F9F6
ERR 14: 00000000 A0022110 20F0E80C
ERR 15: 00000000 A0022110 20F0E7E6
ERR 16: 00000000 A0022110 20F0E7A8
ERR 17: 00000000 A0022110 20F0E790
ERR 18: 00000000 A0022110 20F0E77E
ERR 19: 00000000 A0801001 15713A43
===================================
> bringup
bringup
[SSM] state: 0000 -> 0101
Bringup Mode #0 (0xFF)
[SSM] ssmCb_OnStartingBePowOn() called.
[SSM] First Boot.
[SSM] Bringup mode : syspm_stat=00000000/00000000
[POWSEQ] PowerSeq_Setup called.
[SSM] state: 0101 -> 0301
[SSM] PowSeq Fail : Detected !
[SSM] state: 0301 -> 0700
[POWSEQ] AV Backend Letup
[SSM] Shutdown mode : syspm_stat=00000000/00000000
[ERROR]: 0xa0003001
> becount
[POWSEQ] PowerSeq_Letup called.
[SSM] state: 0700 -> 0600
(PowerOff State) (Fatal)
becount
Bringup : 985 times
Shutdown: 981 times
Power-on: 60day 03hour 55min 06sec
[mullion]$
> errlog
errlog
ofst[120]:err_code:0xffffffff, clock:0xffffffff
ofst[124]:err_code:0xffffffff, clock:0xffffffff
ofst[ 0]:err_code:0xa0801001, clock:0x0fc16e03 2008/05/17 10:20:51
ofst[ 4]:err_code:0xa0801001, clock:0x14e42d73 2011/02/08 16:36:03
ofst[ 8]:err_code:0xa0801001, clock:0x1571381e 2011/05/26 16:11:10
ofst[ 12]:err_code:0xa0801001, clock:0x15713a43 2011/05/26 16:20:19
ofst[ 16]:err_code:0xa0022110, clock:0x20f0e77e 2017/07/06 12:20:14
ofst[ 20]:err_code:0xa0022110, clock:0x20f0e790 2017/07/06 12:20:32
ofst[ 24]:err_code:0xa0022110, clock:0x20f0e7a8 2017/07/06 12:20:56
ofst[ 28]:err_code:0xa0022110, clock:0x20f0e7e6 2017/07/06 12:21:58
ofst[ 32]:err_code:0xa0022110, clock:0x20f0e80c 2017/07/06 12:22:36
ofst[ 36]:err_code:0xa0022110, clock:0x20f0f9f6 2017/07/06 13:39:02
ofst[ 40]:err_code:0xa0022110, clock:0x20f0f9fe 2017/07/06 13:39:10
ofst[ 44]:err_code:0xa0022110, clock:0x20f0fa06 2017/07/06 13:39:18
ofst[ 48]:err_code:0xa0022110, clock:0x20f0fa0a 2017/07/06 13:39:22
ofst[ 52]:err_code:0xa0022110, clock:0x20f101a9 2017/07/06 14:11:53
ofst[ 56]:err_code:0xa0022110, clock:0x20f101b8 2017/07/06 14:12:08
ofst[ 60]:err_code:0xa0022110, clock:0x20f11d36 2017/07/06 16:09:26
ofst[ 64]:err_code:0xa0022110, clock:0x20f11d3b 2017/07/06 16:09:31
ofst[ 68]:err_code:0xa0022110, clock:0x20f11d43 2017/07/06 16:09:39
ofst[ 72]:err_code:0xa0022110, clock:0x20f72f1a 2017/07/11 06:39:22
ofst[ 76]:err_code:0xa0022110, clock:0x20f72f26 2017/07/11 06:39:34
ofst[ 80]:err_code:0xa0022110, clock:0x20f72f64 2017/07/11 06:40:36
ofst[ 84]:err_code:0xa0022110, clock:0x20f72f67 2017/07/11 06:40:39
ofst[ 88]:err_code:0xa0022110, clock:0x213c0d01 2017/09/01 12:20:17
ofst[ 92]:err_code:0xa0022110, clock:0x213c0d08 2017/09/01 12:20:24
ofst[ 96]:err_code:0xa0022110, clock:0x213c0d11 2017/09/01 12:20:33
ofst[100]:err_code:0xa0022110, clock:0x217de5e7 2017/10/21 11:03:03
ofst[104]:err_code:0xa0022110, clock:0x217de5ef 2017/10/21 11:03:11
ofst[108]:err_code:0xa0022110, clock:0x23815b8f 2018/11/16 10:42:23
ofst[112]:err_code:0xa0022110, clock:0x23815b98 2018/11/16 10:42:32
ofst[116]:err_code:0xa0003001, clock:0xffffffff

Now after the becount I think this console is worth saving with only 60 days on ???

THX

 

[DeadEnd]

@Bazilthemage45, @nbdy have a look in here - https://www.psdevwiki.com/ps3/Syscon_Error_Codes

In short, once you see 3034, it's game over for the GPU. There's 3034 in all of your consoles.

@nbdy That sem-001 seems to have a power issue.

 

[nbdy]

[USER=3600]@nbdy That sem-001 seems to have a power issue.[/USER]

Can you guide me further where to look, checked all fuses and they are OK ...

THX

 

[DeadEnd]

Can you guide me further where to look, checked all fuses and they are OK ...

THX

Well, if you read the link, it says 3001 is related to 12v, I guess you already checked the power supply and 12v resistance on board?

Causes for 2110 are also described in the same page. As you can see it can be triggered by many different faults. I have never repaired that board though, I'm not sure what to suggest. You can download the manual and check if 5V_MISC isn't short to ground at least. Inspect the board for damaged/missing components. It's all a shot in the dark at this point. What is the history of the system ?

 

[nbdy]

Well, if you read the link, it says 3001 is related to 12v, I guess you already checked the power supply and 12v resistance on board?

Causes for 2110 are also described in the same page. As you can see it can be triggered by many different faults. I have never repaired that board though, I'm not sure what to suggest. You can download the manual and check if 5V_MISC isn't short to ground at least. Inspect the board for damaged/missing components. It's all a shot in the dark at this point. What is the history of the system ?

I bought the PS3 with RLOD, now have seen the repair guide, and would try to repair it ...

Have more of those board, this board was popular here in Croatia, and many of them have the same issue ...

I'm a hobist elektronic, and would like to repair them to donate to kids in my neiborhood to play which don't have a financial status to buy some of this.

Thx for guiding, will try to download the shematics and to search at it ...

 

[RIP-Felix]

Another CECH-C

>$ bringup
[SSM] state: 0102 -> 0202
[SSM] state: 0202 -> 0103
[SSM] state: 0103 -> 0203
[SSM] ssmCb_BeforeBeOn() called.
[SSM] state: 0203 -> 0104
Psbd_SbTransMode_Half:0x21e2
[SSM] fatalreq delayed.
[ERROR]: 0xa0401001
PLL lock -> unlock
[SSM] *** NON-FATAL EVENT received while fataldown/fataloff, ignored. ***
[ERROR]: 0xa0401301
[POWERSEQ] Error : BitTraining RSX:RRAC:RX0:GLOBAL1:RX_STATUS
[SSM] state: 0104 -> 0304
[SSM] ssmCb_AfterBeOn2() called.
[SSM] *** Power Fail BE ***
[SSM] state: 0304 -> 0700
[POWSEQ] AV Backend Letup
[SSM] Shutdown mode : syspm_stat=00000000/00000000
[ERROR]: 0xa0404402
[ERROR]: 0xa0403034
[ERROR]: 0xa0902120
[POWSEQ] PowerSeq_Letup called.
[SSM] state: 0700 -> 0600
(PowerOff State) (Fatal)

This has to be one of the more interesting brigups I've seen yet.

Hard to know what to make of it. I have been wondering for a while now if the inpeedance of failing BGA or Bumps could cause 1001 errors, or PLL unlocks. The 3034 seems to confirm this.

OTOH, perhaps the 1001/1301 are related to the tokins and the GPU soldering is failing simultaneously (3034/4402). Don't think I've seen a 1001 occur at step# 40 before. Can't remember off the top of my head anyway.