ThatWitcherGuy
Forum Noob
Hello everyone, so I need help on my GLOD CECH-03 ps3 and couldn't think of where else could be the best to ask this question. I want to apoliogise if my english writting is not great.
So i have a ps3 CECHC-03 and it has GLOD, well it didn't until i tried to reflow the RSX. I did so because it started artifacting. The artifacting started after i successfully installed CFW and webman fan mod on the ps3 (it all went fine and didn't crash or start artifacting in the middle of the CFW install), after the CFW install like 10 or 15 minutes later it started to artifact, so I rebooted it and then it was even worse... it couldn't even get past the PS3 boot up logo (in my case evilnat logo). So after that I tried to "reflow" the RSX and now it has the GLOD. For me it seems kind of strange, because when it starts the fan doesn't spin up to what I set it to in the webman setup, or maybe this is completely fine because the ps3 does not but up properly? So here I am asking for help.
If this is helpfull the hdd light flashes 1 time and never flashes again. I tried putting in a disc into the disc drive and it takes and "spits out" the disc absolutely fine (I have read that if does not do so It might be a bad CPU or something similar, which to my knowledge is really bad).
I have bought a USB TTL adapter so I could see the southbridge logs and boot order to see where does it get stuck on, but I kind of don't understand how to do so. I have found DeadEnd's guide on how to do it but for me personaly the guide is unclear (I am not saying it is a bad post), like I kind of understand on how and where to solder the wires, but to get the logs and boot order, for me it is not understandable (again im not saying the post is bad, it's great). I would love if someone could give me a step by step guide/tutorial on how to get the southbridge logs and the boot up order. I know im asking a lot, but any help will be appreciated.
Don't need it anymore.
So i have a ps3 CECHC-03 and it has GLOD, well it didn't until i tried to reflow the RSX. I did so because it started artifacting. The artifacting started after i successfully installed CFW and webman fan mod on the ps3 (it all went fine and didn't crash or start artifacting in the middle of the CFW install), after the CFW install like 10 or 15 minutes later it started to artifact, so I rebooted it and then it was even worse... it couldn't even get past the PS3 boot up logo (in my case evilnat logo). So after that I tried to "reflow" the RSX and now it has the GLOD. For me it seems kind of strange, because when it starts the fan doesn't spin up to what I set it to in the webman setup, or maybe this is completely fine because the ps3 does not but up properly? So here I am asking for help.
If this is helpfull the hdd light flashes 1 time and never flashes again. I tried putting in a disc into the disc drive and it takes and "spits out" the disc absolutely fine (I have read that if does not do so It might be a bad CPU or something similar, which to my knowledge is really bad).
I have bought a USB TTL adapter so I could see the southbridge logs and boot order to see where does it get stuck on, but I kind of don't understand how to do so. I have found DeadEnd's guide on how to do it but for me personaly the guide is unclear (I am not saying it is a bad post), like I kind of understand on how and where to solder the wires, but to get the logs and boot order, for me it is not understandable (again im not saying the post is bad, it's great). I would love if someone could give me a step by step guide/tutorial on how to get the southbridge logs and the boot up order. I know im asking a lot, but any help will be appreciated.
Don't need it anymore.
Last edited by a moderator:
