ps3 slim

so, i have a ps3 cech-2504a with a overheating rsx 45nm, the model i think is not the glued one ( serial no: 03-27456822-5906307) and i wanted to delid it, but the glue on the vram modules is insanely hard, so hard that not even heating it and cutting with a modified painter scalpel (paper thin)...

Hi guys. I need help with this ps3 slim. It's 2000 DYN board. It had errors with 12V (light was dim) and upon inspection with thermal camera i saw syscon getting warm. Afrer removing syscon the light was bright and i was able to get those 12V, so syscon was causing short. I have syscon on same...

Hello, some time ago I have a ps3 slim CECH2001A, It had never suffered from overheating or anything, but one day while I was playing there was a power outage in my house and after that my console only shows YLOD, I do not think it is a matter of reballing because as I say never suffered from...

My ps3 slim sounded like a jet engine while playing, so i decided to put new thermal paste on. After disassembling and reassembling the console, i realized that i had broken the ribbon for the power button, which sucks but isnt the end of the world. i plugged my controller in and got my ps3 to...

Ok, I’m dealing with a strange issue with my 2504A, and I can’t seem to figure out the cause. Sometimes when I try to turn on the PS3, it immediately shuts down after the LED turns green. At this point, the LED stays off, and pressing the power button doesn't turn it back on or make it go red...

Hi i just changed thermal paste and cleaned my ps3 slim (CECH-2504B) my room temp is 30c° and after 2 hours of gta v the cpu is 59c° and rsx 64c° at manual fan speed 65% are these temp good ?

Quite recently, my beloved Delta KFB1012HE died abruptly, which made me more interested in the different models available for the Slim (specifically for the 20XX/21XX/25XX). There are some topics and videos about FAT's fans models comparison (efficiency, noise, etc...) but practically nothing...

Hello friends, I have to repair a KEM 450 Disc drive for my PS3 slim. The issue is that when it pulls the Disc in, it "tries" to read it but the clock just keeps spinning. Then you can hear the Disc drive trying to eject the Disc and the clock stops. Ejecting works normally. When I opened it...

Hello fellow members of the PSX Place community, I picked up a CECH-2004a and 2 controllers on FB Marketplace for 28€ which has a disc drive issue, it being the game wont read. A "Technichian" from the Seller tried fixing it but to "no avail" (He lost all the screws holding the 2 Cases together...

Was playing when it suddenly died. At first, I thought that it could be a software issue, as when I quitted the game, it re-worked. But later, it died on the XMB and for good this time :\ It was set to 40% minimum speed, and almost never needed to go up to 41%. I don’t think that the speed could...

hy to yall, i have a ps3 cech-25xx, it was heavily used and so the thermal paste between the rsx and cell is completely dried up, i already delidded the cell but the rex heat spreader is on extremey well... i tried with heat but nothing. i tried cutting it with a sharp painter knife but it's so...

Hi everyone, find PS3 slim model CECH-2508A , board JTP-001 , won't turn on OK , I started to open and find something interesting cell fell out, tracks torn out , and an unknown capacitor that does not exist. Plz help Shem I don't found maybe anyone have Shem or know capacitor rating

Console: CECH-2001A FW Type: CEX Cobra Cobra Version: 8.5 Cobra FW Version: 4.91 Main Software Used: IrisMan, MMCM, and ManaGunZ SYSCON Error Log: Firmware Version: 4.91 (build 50754) Platform ID: CokG11 Product Code: 00 84 Product Sub Code: 00 09 Hardware Config: 000000000203BC3C Syscon...

Hi I bought a PS3 slim that has a glod as a project to try and fix it but im not sure what is going on. It was full in dust so i cleaned everything in it and then tried to start it up but this didn't fixed it. When it turns on the hdd light blinks only once and then nothing it just sits at green...

Help needed please :deank: :psbutton:

Hi, I'm looking everywhere and I can't find a clear answer, should I replace the IHS thermal paste under CELL and RSX in the CECH-3004A model? or only under RSX? What about super slims CECH-4004C? I read about this and there is too no clear answer about that. I know, if they work fine, I should...

I want to uninstall it cuz everytime I enable HEN my console freezes. I've tried reinstalling HFW already and HEN but didn't worked at all. There is no HEN toolbox under PS3 game data in the XMB menu. Where is the Hen toolbox stored on the hard drive so I can remove it manually? Note that the...

It used to happen also on HFW 4.90 with HEN 3.2.0. That's why I have made a reinstall (couldn't find 4.90). I also had installed Hen Toolbox and that's probably the issue even through it's disabled. By the way I can't uninstall it. I have seen a thread about this and some guy said that reinstall...

Hello everyone. Recently my PS3 Slim stopped working all of a sudden with GLOD. The system would beep, the led changes from red to green, but nothing is displayed on the TV screen, then it shuts off after 60 seconds with no led light, no yellow, no red, no nothing. I already tried changing the...

PS3 Slim 2504A got it used 2016 and it's been hassle free since it just stopped working a couple years ago, when press pws I get green light for half a second then it turns off, when I press it again it goes back to standby. I opened it up and noticed that the bottom board cover bent next to the...